Hepco & Becker engine guards provide protection in case of an accident or fall. Custom designed for each bike to bolt on without drilling. All engine guards come with the required installation hardware and instructions.
The NT1100 can be outfitted with auxiliary fog lights from the factory. If so, you will need the light mounting kit Hepco & Becker has specially designed for this so you can mount the engine guard and lights together. You can find it HERE!
This part fits these bikes
- Honda NT1100 (2025–2026)
The lower engine crash bars arrived quickly, well-packaged and will all the right hardware. The installation instructions were a bit awkward to read as they were clearly translated from German. Be sure you have specialized tools like ratchet box wrenches to get into tight spots and exercise some patience. It will all fit if you do it right and in order.
Note that you need the lower bars in order to install the uppers because the uppers attach to the lowers.
The bars were delivered in a matter of a few days. They are of high quality and included thorough instructions although there is room for misunderstanding. You should read the entire instructions and identify all of the parts. I found it unnecessary to remove the brake pedal and the skid guard. I’m very satisfied with the final result. I added a few plastic “sliders”.
Quality is good. Need to improve the installation directions.
bars are well made.. nice welds and paint. instructions are a little confusing.
These engine crash bars are well made and are a perfect fit on my 2025 Honda NT1100 DCT.
These bars look great and should do a good job . I had them installed at the dealership so cannot come in on ease of installation or instructions.
The bars are compact yet offer great protection. Look good on the bike and we're pretty easy to install. One area in instructions was not very clear. Instructions could use better translation.
Very easy to install and very sturdy. A must buy! Note: The center fitting (under the radiator) did not completely close together in to the joint fitting. There was about 1/8” (5mm) space. This did not cause any issue, but only concern is water. Understand fabricating pipe is not precise, but supplying a few different washer/spacer would have help. Likely most installs don’t have this issue.
Lower engine guards perfectly fit my2026 NT1100
Was not clear, about fitment for the 26. I can confirm, fits without trimming guards and deflectors. Very solid, because these are fully welded and don't have all the little brackets bolted on, like other brands.
fits good and easy
Everything was exactly as ordered! Undamaged and looking good.
Fit perfectly. High quality parts.
Ordered the lower and upper Sets. They were delivered promptly, good, solid quality with good instructions. If you follow the instructions they are fairly easy to install, with the exception of 1 bolt on top and one on bottom. Those 2 bolts were difficult.
So. . . the H&B's come from Germany with the majority of the instructions in German. . . and few pictures. There were probably son short cuts I could have used to make it easier. . . but they got installed. . . and look good on the bike
Only drawback is installation is not the easiest but that is on Honda rather than H+B.
The bars are great, i had the local motorcycle shop install them because they were installing my fog lights and needed them installed. They fit great and look great.
I am in the USA and I recently purchased and installed the Hepco & Becker crash bars for the new Honda 2025 NT1100 DCT. They were shipped quickly after being restocked in the distribution center in the States. I watched an install on the internet and read the provided instructions. The install was easily accomplished by 1st removing all the bolts (& nuts where required) and then fitting the new crash bars - 1st the left side - where I needed another pair of hands to hold the rear edge bottom of the left side while I installed the long bolt & nut at the front. Plus I needed another pair of hands holding the same spot (bottom and rear edge) of the right side when I moved again in the front and connected the 2 side together. I then finished the install of the other bolts and tightened to specs. Fit was perfect! Great quality! Only thing I would add to the notes for install: when installing the nut to the long bolt in the front - tape the nut to an open end box wrench when trying to get the nut started on the ends of the long bolt. ( I lost the original nut somewhere in the bottom pan of the bike). Hepco & Becker are very well engineered. I also installed their Saddlebag protectors - another great installation!
The crash bars are precisely engineered to protect the Honda NT1100 motorcycle. We are absolutely delighted with this purchase. Moto Machines is a great company to work with and provided excellent customer support.